Best Sales Famous Brand SRS3-P-N10-001 Digital Indicating Instrument

• Customization: Available
• Customized: Customized
• Certification: RoHS, CB, CCC, ISO9001, CE
• Model NO.: SRS3-P-N10-001
• Display Type: LED
• Weight: 190g
• Data Storage: by Non-Volatile Memory (Eeprom)
• Ambient Temperature: -10~50ºC
• Supply Voltage: 100-240VAC+/-10%(50/60Hz)
• Power Consumpsion: 10va
• Transport Package: Board Box/Carton
• Specification: 92*92
• Trademark: SHIMADEN
• Origin: Japan
• HS Code: 90321000
• Production Capacity: 10000

Product Description

1.SRS0 Series Instruction:
   (1-1) Preliminary check
The controller has undergone sufficient quality control inspections, but you should check the specification code/appearance
and make sure you have all the accessories to make sure nothing is missing or damaged.
Compare the specification code on the case with the following to make sure it is the product you ordered.
   (a)Model mode Check:
       (b)Accessories Check:
       Instruction Manual (A3 size paper x 2): 1 copy 
       Unit seals:                                              1 sheet 
   Note: In the event you want to inquire about a product defect, missing accessory or other matter, please contact our salesman directly;
(1-2)Notes before use: 
   Do not press front panel keys with a hard or pointed object. Press lightly with your fingertips.To clean, wipe lightly with a dry cloth. Do not use solvents such as thinner.
2.Installation&Wiring: 
   (2-1)Installation site (environmental conditions)
    Environmental conditions for operations
     The controller is designed to be used under the following conditions. Observe the following environmental conditions when using:
    1) Must be used indoors;2)Max.elevation: 2000m; 3) Ambient temperature: -10-50°C;4) Ambient humidity: Max. 90%RH, no dew
condensation;5) Transient over voltage category: II; 6) Pollution class: 2 (IEC 60664);
≡Caution:
   Do not use the controller in the following locations.Doing so could lead to equipment failure, damage or fire.
   * Places exposed to flammable or corrosive gases, oil mist, or excessive dust that could cause insulation to deteriorate.
   * Places subject to vibration or impact.
  * Places near strong electric circuit or places subject to inductive interference.
  *  Places exposed to water dripping or direct sunlight.
  * Places where the controller is struck directly by air from heater or air conditioner.
(2-2) Mounting: 
      1) Cut a hole for mounting the controller in the panel by referring to "3.3. External dimensions and panel cutout."
       2) The panel thickness should be 1.0-3.5 mm.
       3) The controller is provided with tabs for mounting. Insert as is from the front surface of the panel.
       4) Controllers of the SRS0 Series are designed for mounting on the panel. Be sure to mount on the panel.
       5) If mounted in series, provide ventilation so ambient temperature does not exceed 50°C due to temperature rise caused
           by heat generation.
  ≡Caution:
     In order to maintain safety and function, do not remove the case from the controller.
     If the case of the controller has to be removed for replacement/repair, contact your nearest Shimaden agent.
(2-3)External dimensions and panel cutout
     (2-4)Wiring
≡Caution:
Be sure to turn off power before wiring. Failure to do so could result in electric shock.
After wiring, do not touch terminal elements or other charged parts while conducting electricity.Failure to do so could result in electric shock.
Take the following precautions when wiring:
1) Wire in accordance with the terminal layout of section 3-5 and the terminal arrangement table of section 3-6.
After wiring, check and make sure the wiring is correct.
2) Crimp-type terminals fit M3 screws. Use crimp-type terminals that are no wider than 6 mm.
3) For thermocouple input, use a compensating conductor that matches the type of thermocouple.
4) For RTD input, resistance for lead wires should be a maximum of 10   per wire.
All 3 wires should have the same resistance.
5) Input signal wires must not be accommodated with a strong electric circuit in the same conduit or duct.
6) Using shielded wiring (single point grounding) is effective for static induction noise.
7) Making input wiring short and twisting at regular intervals is effective for electromagnetic induction noise.
8) For power supply, use wiring or cable with sectional area of at least 1 mm² that offers the same performance as 600 V
vinyl insulated wiring.
9) Securely fasten the terminal element screw. Fastening torque: 0.5 N·m (5 kgf·cm)
10) If the instrument appears to be easily affected by power supply noise, use a noise filter to prevent malfunctioning.
Mount the noise filter on the grounded panel and make the wire connection between the noise filter output and power
line terminals of the controller as short as possible.
(2-5)  Terminal Layout
Wire in accordance with the following terminal layout and terminal arrangement table.
(2-6) Terminal Arrangement Table:

Name of terminal	Description	Terminal No.
		SRS1	SRS3/4/5
Power supply	100-240 V AC 100-240 V AC	7 8	13 14
Input	RTD: A, thermocouple/voltage: + RTD: B, thermocouple/voltage: - RTD: b	4 5 6	22 23 24
Control output 1	Contact: NO, SSR drive voltage/voltage/current: + Contact: NO, SSR drive voltage/voltage/current: -	9 10	15 16
Event output	COM EV1 EV2	1 2 3	19 20 21
External control input/DI	COM DI1	11 12	17 18

Note 1: With thermocouple/voltage input, shorting across B and B terminal will cause an error;
(2-7) Operation preparations
Before operating the controller, you should first check the wiring and carry out the following by screen group setting method.
There is however no need to change the settings that have been set at the factory or already been made by the manufacturer.
1. Wiring check
Make sure the wiring to the connection terminals is correct. Incorrect wiring could result in burnout.
2. Power ON
Turn on the operating power. The displays, etc., light when power is supplied to the controller.
3. Measuring range setting
Select code from Measuring Range Codes of "5-10. Measuring range codes setting screen" of 5 screen group and enter.
Select temperature unit of "5-11. Input unit setting screen" of 5 screen group and enter.
For mV input, set lower limit value, higher limit value and position of decimal point of display contents for input signal.
(You should also select by 5-12, 5-13, 5-14, 5-15, and 5-16 screens by code.)
4. Control mode (PID) setting
For ON-OFF (2 position) action, select OFF by "2-1. Output PID1 proportional band setting screen" of 2 screen group
and enter. Sets hysteresis by "2-2. Output PID1 hysteresis setting screen." If using auto tuning (AT) with other than
ON-OFF hysteresis, this setting operation is not required.
5. Control output characteristics setting
Select RA (for heating) or DA (for cooling) according to output specification (heating/cooling) on "5-3. Output
characteristics setting screen" of 5 screen group and enter.
6. Event type setting
Select types of event on "4-1 and 4-7 Event 1/2 type setting screen" of 4 screen group and enter.
7. Precaution concerning initialization by data modification
Modifying measuring range code or type of event initializes related setting values (data). The data must therefore be set
again.
3.Names and functions of parts on front panel

Name	Function
1) Measured value (PV) display	1. Measured value display LED (red) Displays current measured value (PV) on basic screen (screen 0-0). Displays type of parameter on each respective parameter display screen.
2) Target set value (SV) display	2. Target value display LED (green) Displays current target set value (SV) on basic screen (screen 0-0). Displays setting values on each respective parameter setting screen.
3) Action display	Displays status of controller. RUN: Action display LED (green) Off:            Control halt status (standby or reset) On:             Running by fixed value control status (FIX) Flashing:  Running by program control status (RUN) OUT: Control output (green) For output by contact or SSR drive voltage: Off:            Output is OFF. On:             Output is ON. For voltage/current output: Off when output is 0% and On when output is 100%. In other cases, flashes at intervals of 0.5 seconds (multiples of 0.5 sec.). AT: Auto tuning LED (green) Off:             Auto tuning not executed On:             Auto tuning standby Flashing:  Auto tuning being executed MAN: Manual control LED (green) Off:             Automatic control operating status Flashing:  Manual control operating status EV1: Event output 1 (orange) EV2: Event output 2 (orange) Off:             Event output is OFF. On:             Event output is ON.
4) Operating keys	Parameter key Displays the next screen in various screen groups.  Down key Decrements setting values.  Up key Increments setting values.  Enter key Enters setting values.  Displays various screen groups if no SV values are being modified on the basic screen.

4. Measuring range codes
Select measuring range from the following table.
Note: Changing the code initializes all data related to measuring range. Change setting after switching
to reset mode from the 0-1 screen.

Input type			Code	Measuring range (°C) Measuring range ( )
	Kelvin	B *6	*1	0-1800°C 0-3300
		R		-50-1700°C 0-3100
		S		0-1700°C 0-3100
		K	*2	-199.9-400.0°C -300-750
				0-1370°C 0-2500
		E		0-700°C 0-1300
		J	*2	-200-600°C -320-1100
		T *6	*2	-270-400°C -450-750
		N		0-1300°C 0-2300
		PL ll *3		0-1300°C 0-2300
		C(WRe5-26)		0-2300°C 0-4200
		U *3	*2	-199.9-400.0°C -300-750
		L K	*4	0-600°C 0-1100 10.0-350.0K
		AuFe-Cr	*5	0.0-350.0K
	RTD	Pt100		-199.9-300.0°C	-300-600
	mV	-10-50 mV		Scaling range: -1999-9999 digit Span: 9999 digit
Voltage	V	0-10 V

*1 Thermocouple B: Accuracy guarantee is not applicable to 400°C (750°F) or below.
*2 Thermocouple K, J, T, U:
Accuracy of indicated values below -100°C and -148°F is ± (1.5%FS + 1 digit).
*3 Thermocouple PL ll, U: Accuracy of indicated values is ± (1.5%FS + 1 digit + 1°C).
*4 Thermocouple K (Kelvin) accuracy temperature range:
10.0-30.0K: ±(2.0%FS + 1 digit) Provided the wire resistance is 10 or below
31.0-70.0K: ±(1.5%FS + 1 digit) Provided the wire resistance is 10 or below
71.0-350.0K: ±(1.0%FS + 1 digit)
*5 Thermocouple AuFe-Cr: Accuracy of indicated values is ± (1.0%FS +1digit).
*6 Thermocouple B, T:
Accuracy of indicated values below these temperatures is subject to wire resistance 50 or below:
B: 500°C (930°F)
T: -240°C (-400°F)
*7 Temperatures below -273°C (-459°F) are subject to scaleover display.
*8 With or without a decimal point is selectable for TC and Pt.
Note: Unless otherwise designated, the factory default settings are as follows:

Input range	Code	Measuring range
Multi-input		K 0-1370°C
Voltage input		0-10 V

5.Specification Details:
Display
Digital display: Measured value (PV): 7-segment red LED, 4 digits
Target set value (SV): 7-segment green LED, 4 digits
Action display: LED lamp display: Color
Auto tuning (AT): Lights during standby (flashes during execution): Green
Action display (RUN): Lights during fixed value control operation (FIX): Green
Flashes during program RUN program control operation (RUN): Green
Control output (OUT): Lights during contact or SSR drive voltage output: Green
For voltage/current output, lights when output is 100%
In other cases, flashes at intervals of 0.5 sec. (multiples of 0.5 sec.).
Manual control output (MAN): Flashes during manual output is ON: Green
Event (EV1, EV2): Lights during event output: Orange
Display resolution: Differs according to input range (0.001, 0.01, 0.1, 1)
Display accuracy: TC: ±(0.3%FS + 1 digit + 2°C)
Pt: ±(0.3%FS + 1 digit + 0.1°C)
mV: ±(0.3%FS + 1 digit)
Display cycle: 500 ms
Setting
Setting method: By operating 4 front panel keys( , , , )
Input range setting: Input range within measuring range is arbitrarily settable.
SV limiter: Settable within both measuring range and input range.
Setting lock: OFF, 3-stage setting (1-3)
Input
Input common specification
Input type: Multi input
Input Scaling: Valid when voltage input
Display range: Voltage input (mV, V)
Display scaling range -1999  9999 digit
Display scaling span: 10  9999 digit
Decimal point position:   Without, settable from 0.1, 0.01, or 0.001 (With or without a decimal point is selectable for TC and Pt.)
PV bias: -1999-2000 digits
PV ramp: 0.500-1.500 times input value
PV filter: OFF, 0-9999 sec.
Scaleover display: LLLL, HHHH
Isolation: Uninsulated from system and DI, but insulated from other input
Thermocouple input (TC)
Input type: B, R, S, K, E, J, T, N, PL  ll, C(WRe5-26), AuFe-Cr, {U,L (DIN43710) }
Display range: Within PV limiter (provided that minimum temperature does not fall below -273.15°C)
With or without a decimal point is selectable.
Input resistance: 500k
Cold junction
compensation: Internal
Internal cold junction
compensation accuracy: ±2°C (18-28°C)
Burnout function: Only upscale
External resistance
tolerable range: 100  or below
RTD input
Input type: Pt100, 3-wire type
Display range: Within input range setting (provided that minimum temperature does not fall below -240°C)
With or without a decimal point is selectable.
Lead wire tolerable
resistance range: Below 10   /1 wire (All wires should have the same resistance.)
Measured current: Approx. 0.25 mA
Voltage input
Input type: -10-50 mV DC, 0-10V DC
Input resistance: Approx. 500k  or above
Control mode
Expert PID control with auto-tuning function
No. of SV: 2
No. of PID: 2 classes
Proportional band: OFF, 0.1-999.9% (ON-OFF action when OFF)
Integral time: OFF, 1-6000 sec. (P or PD action when OFF)
Derivative time: OFF, 1-3600 sec. (P or PI action when OFF)
Manual reset: -50.0-50.0% (Valid when I = OFF)
ON-OFF hysteresis: 1-999 digits (Valid when P = OFF)
Proportional cycle: 1-120 sec., 1 sec. step
Control output
characteristics: Reverse/direct selectable
Manual output: 0.0-100.0 %, 0.1% step
Output update cycle: 500 ms
Manual control: Balanceless/bumpless action (switch through front panel key switch or external control input [DI])
Output setting range: 0.0-100.0%
Setting resolution: 0.1%
Control output
Contact (Y): Contact (1a), 240V AC, 2.5 A: Resistive load/1 A: Inductive load
SSR drive voltage (P):  12 V ± 1.5 V DC (max. load current 20 mA)
Current (I): 4-20 mA, max. load resistance 600
Voltage (V): 0-10 V, max. current 2 mA
Output resolution: 10000 digits
Event output (EV)
No. of output: Standard 2 points (EV1-EV2)
Constant rating: Contact (1a), 240 V AC, 1 A: Resistive load (common)
Function: Display: Action
Hd: Higher limit deviation value action
Ld: Lower limit deviation value action
od: Outside higher/lower limit deviation action
id: Inside higher/lower limit deviation action
HA: Higher limit absolute value action
LA: Lower limit absolute value action
SO: Scaleover
RUN: Control execution
ROT1: Control output inverted output (contact output only)
STPS: Step signal
PTNS: Pattern signal
ENDS: Program end signal
HOLD: Hold signal
PROG: Program signal
U_SL: Upslope signal
D_SL: Downslope signal
GUA: Guarantee soak
Setting range
Absolute value: Within both measuring range and PV limiter (both higher and lower limit)
Deviation: -1999-2000 digits (both higher and lower limit)
Higher/lower deviation:  0-2000 digits (both inside and outside)
Action: ON-OFF action
Hysteresis: 1-999 digits
Action delay time: OFF, 1-9999 sec.
Standby action: Separate setting (separate output), selectable from any of 4 types below
1) Without
2) Standby 1 (when starting power, when RST ON OFF)
3) Standby 2 (when starting power, when RST ON OFF, when execution SV is changed)
4) Standby 3 (Does not output when there is input abnormality.)
Latching: Selection from Yes/No
Output characteristics:  Selection from NO/NC
Output update cycle: 500 ms
Isolation: Insulated from all input and output (uninsulated within EV)
External control input (DI)
No. of input: Standard 1 point
Input type: Level input, edge input
Input rating: Voltage 5 V DC (2.5 mA/1 input)
Input action: Non-voltage contact or open collector
Input holding time: 500 ms
Function: Display: Action: Input type
RUN1: Starts control when ON: Level
RUN2: Starts control when ON: Edge
MAN: Manual control output mode: Level
AT: AT execution: Edge
SV: SV switch: Level
RAMP: Ramp halt: Level
ACT: Output characteristics: Level
L_RS: Event latching release: Edge
PROG: Program switch: Level
HLD: Hold signal: Level
ADV: Advance signal: Edge
Program (option)
No. of pattern: 1
No. of step: 10
Power failure
compensation: Without
Guarantee soak zone: oFF, 1-999 digits
Time accuracy: Set value × 0.3%
General specifications
Data storage: By non-volatile memory (EEPROM)
Operating ambient
Ambient temperature:   -10-50°C
Humidity range: Below 90%RH (no condensation)
Derating from 50°C
Storage temperature: -20-65°C
Over voltage category:   ll
Elevation: Max. 2000 m
Pollution class: 2 (IEC 60664)
Supply voltage: 100-240 V AC ± 10% (50/60 Hz)
Power consumption: 10 VA
Input noise removal ratio:   Normal mode: 50 dB or above (50/60 Hz)
Common mode: 120 dB or above (50/60 Hz)
Common mode: 120 dB or above (50/60 Hz)
Applicable standard: Safety:  IEC61010-1 and EN61010-1
IEC61010-2-030 and EN61010-2-030
EMC: EN61326-1
Power supply
short-break time: Within 50 ms, normal action continuation (when 200V)
Insulation resistance: Input-output terminal and power terminal interval, 500 V DC, 20M  or above
Dielectric strength: Input-output terminal and power terminal interval, 2300 V AC, 1 min.
Material of case: Resin mold (UL94V-1 equivalent)
External dimensions: SRS1: H48 × W48 × D66 mm, panel depth: 62 mm
SRS3: H96 × W96 × D69 mm, panel depth: 65 mm
SRS4: H96 × W48 × D66 mm, panel depth: 62 mm
SRS5: H48 × W96 × D66 mm, panel depth: 62 mm
Mounting: Panel flush mounting
Applicable panel thickness:  1.0-3.5 mm
Panel cutout: SRS1: H45 × W45 mm
SRS3: H92 × W92 mm
SRS4: H92 × W45 mm
SRS5: H45 × W92 mm
Weight: SRS1: Approx. 100 g
SRS3: Approx. 190 g
SRS4: Approx. 120 g
SRS5: Approx. 120 g
6. FAQ
Q1.What advantages do you have?
A1. Solex is the direct Manufacturer in Cangzhou city, China, we have professional developing, marketing & production team to offer you the most competitive price and best service.
Q2. What's your main product?
A2. We have three product series~solid state relay, thyristor regulator(power &voltage), Wafer making furnace heater;
Q3. Could you print our own logo?
A3. Yes, our company are available for Retail & Wholesale & OEM & ODM.
Q4. How long is the quality guarantee?
A4. 18 month warranty, our products are 100% inspected before leaving factory.
Q5. How long is the deliver time?
A5. It usually takes about 3 - 5 working days for sample order and 10 - 25 days for big order.
Q6. What is your payment terms?
A6. T/T, Western Union, Money Gram, L/C at sight,etc.
Q7. Any certification of your company or product?
A7.We have ISO 9001,CE,CB,TUV, etc.